1/6 thick film chip resistors mcr series www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2016.06 - rev.j da t asheet ? features 1) full line up from ultra small size (01005) to 2512 with jumper type. 2) high reliability metal glazed thick film. 3) rohm resistors have obtained iso9001/iso/ts16949 certification. part no. packing specification quantity / reel (mm) type code size paper tape (2mm pitch) embossed tape (4mm pitch) 04020603 1005 1608 2012 3216 3225 5025 6432 01005 0201 - 04020603 0805 1206 15,00010,000 paper tape (4mm pitch) 5,000 automotive grade available aec-q200 yes 4,000 yzp ylp mzp ezp 1210 jzh 20102512 mcr004mcr006 mcr01 mcr03 mcr10 mcr18 mcr25 mcr50 mcr100 (inch) ? part number description 04 mcr (micro chip resistors) 0y p z c mr part no. resistance code, 3 or 4 digits.000 denotes jumper type. ex.) 1 = 1r0 ( 5% ) 9.1 = 9r1 ( 5% ) 10 = 10r0 ( 0.5%, 1% ) 100 ( 5% ) 2.2m = 2204 ( 1% ) 225 ( 5% ) d,f j :: 4 digits3 digits resistance tolerance resistance code 004 (0402 [01005])006 (0603 [0201]) 01 (1005 [0402]) 03 (1608 [0603]) 10 (2012 [0805]) 18 (3216 [1206]) 25 (3225 [1210]) 50 (5025 [2010]) 100 (6432 [2512]) d ( 0.5% ) f ( 1% ) fx ( 1% ) ? only mcr03ezp j ( 5% ) (including jumper type) size (mm [inch]) resistance tolerance nominal resistance j0 10 type code downloaded from: http:///
2/6 da t asheet mcr series www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2016.06 - rev.j ? products list limiting element voltage (v) temperature coefficient (ppm / c) resistance tolerance (%) operating temperature range ( c ) type code resistance range series part no. rated power (70 c) (w) mcr006 ylp mcr01 mzp 0.05 25 jumper type : rmax = 50m / imax. = 0.5a jumper type : rmax = 50m / imax. = 0.5a jumper type : rmax = 50m / imax. = 1a jumper type : rmax = 50m / imax. = 1a jumper type : rmax = 50m / imax. = 2a jumper type : rmax = 50m / imax. = 2a jumper type : rmax = 50m / imax. = 2a jumper type : rmax = 50m / imax. = 3a jumper type : rmax = 50m / imax. = 4a 5050 150200 200 0.063 ezpezp ezp jzhjzh mcr03mcr10 mcr18 mcr25 mcr100 0.10.1 0.125 0.25 1 400 j( 5%) fx( 1%) d( 0.5%) j( 5%) f( 1%) j( 5%) j( 5%) f( 1%) f( 1%) ? 55 to + 125 ? 55 to + 155 ? 55 to + 125 d( 0.5%) 100 50 100 200 1.0 10 100 10 10 e24 e24,e96 e24 e24,e96 e24 e24,e96 e24 e24,e96 1.0 2.2 5.6 500 350 500 200 + 600 / ? 200 j( 5%) f( 1%) d( 0.5%) 250 100 200 250 1.0 10 1k 10 10 e24 e24,e96 + 500 / ? 250 j( 5%) f( 1%) d( 0.5%) 100 50 100 200 1.0 10 100 10 10 e24 e24,e96 500 350 350 100 200 500 1.0 10 10 24 2.2 200 jzh mcr50 0.5 j( 5%) f( 1%) e24 e24,e96 500 350 200 100 350 500 1.0 10 10 360k 2.2 400 100 50 100 200 1.0 10 100 10 10 200 0.125 0.25 j( 5%) f( 1%) d( 0.5%) e24 e24,e96 400 100 50 100 200 1.0 10 100 10 10 10 toto to to toto to to toto to to toto to to to toto to to to to toto to to to toto to to toto to to to toto 100 ? design and specifications are subject to change without notice. carefully check the specification sheet supplied with the produ ct before using or ordering it. ? rated voltage is determained from the following. when rated voltage exceeds the limiting element voltage, the limitng element voltage shall be the rated voltage. ? rated voltage = ? e24 : standard products, e96 : custom products rated power rasistance 9.1 10m 1m 91 10m 2.0 5.1 3.3m 9.1 10m 1m 910 10m 9.1 2.2m 1m 91 10m 2.0 22 82k 100k 9.1 2.0 330k 180k 560k 9.1 9.1 2.2m 1m 91 10m 9.1 2.2m 1m 91 10m 1m mcr004 yzp 0.031 15 300 j( 5%) f( 1%) 250 300 250 91 9.1 3m 91 3m + 600 / ? 200 e24 e24,e96 10 1.0 100 10 100 to toto to to downloaded from: http:///
3/6 da t asheet mcr series www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2016.06 - rev.j ? chip resistor dimensions and markings < marking method> there are three or four digits used for the calculation number according to iec code and ris used for the decimal point. part no. type code (mm) (inch) l w t a b marking existence (unit : mm) mcr006 ylp 0603 0201 0.6 0.03 0.3 0.03 0.23 0.03 0.1 0.05 0.15 0.05 no mcr01 mzp 1005 0402 1.0 0.05 0.5 0.05 0.35 0.05 0.2 0.1 no mcr03 ezp 1608 0603 1.6 0.1 0.8 0.1 0.45 0.1 0.3 0.2 0.3 0.2 yes ? mcr10 ezp 2012 0805 2.0 0.1 1.25 0.1 0.55 0.1 0.4 0.2 0.4 0.2 yes mcr18 ezp 3216 1206 3.2 0.15 1.6 0.15 0.55 0.1 0.5 0.25 0.5 0.25 yes mcr25 jzh 3225 1210 3.2 0.15 2.5 0.15 0.55 0.15 0.5 0.25 0.5 0.25 yes mcr50 jzh 5025 2010 5.0 0.15 2.5 0.15 0.55 0.15 0.6 0.25 0.6 0.25 yes mcr100 jzh 6432 2512 6.3 0.15 3.2 0.15 0.55 0.15 0.6 0.25 0.6 0.25 yes 0.25 + 0.05 ? 0.1 mcr004 yzp 0402 01005 0.4 0.02 0.2 0.02 0.13 0.02 0.1 0.03 0.1 0.03 no marking method of jumper type jumper typemcr004 / 006 / 01 / 25 / 50 / 100 mcr03 / 10 / 18 no yes marking existence ? marking method of mcr25/50/100 blueglass over coat is used for the jumper type. there is no marking on the jumper type. ? marking method of mcr03 for mcr03 series resistors, the printing process re stricts the marking to th ree digits/characters. consequently, 1% tolerance resistors with values from the e24 series will be marked the same as 5% resistors with the same value, but 1% tolerance resistors with values from the e96 series will not be marked. examples: mcr03ezpj243 (5% tolerance, e24 / 24 k ? ) marking = 243 mcr03ezpfx2402 (1% tolerance, e24 / 24 k ? ) marking = 243 mcr03ezpfx2432 (1% tolerance, e96 / 24.3 k ? ) no marking mcr18ezpj243 (5% tolerance, e24 / 24 k ? ) marking = 243 mcr18ezpf2402 (1% tolerance, e24 / 24 k ? ) marking = 2402 mcr18ezpf2432 (1% tolerance, e96 / 24.3 k ? ) marking = 2432 ? land pattern example b d a land c b bb 103 l l w w t t a aa mcr004 / 006 / 01 / 03 mcr10 / 18 / 25 / 50 / 100 mcr004 mcr01mcr03 mcr10 mcr18 mcr25 mcr50 mcr100 yzp mzp ezpezp ezp jzhjzh jzh 0.20.5 1.0 1.2 2.2 2.2 3.8 5.1 0.41.3 2.0 2.6 4.0 4.0 6.0 8.1 0.16 0.50.8 1.15 1.52.3 2.3 3.0 0.10.4 0.5 0.7 0.9 0.9 1.1 1.5 mcr006 ylp 0.3 0.84 0.3 0.27 dimensions part no. type code a b c d (unit : mm) downloaded from: http:///
4/6 da t asheet mcr series www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2016.06 - rev.j ? derating curve when the ambient temperature ex ceeds 70c, power dissipation must be adjust ed according to the derating curves below. 0 20 40 60 80 100 ? 55 0 70 100 125 ambient temperature ( c) percent rated power (%) mcr004 / 006 / 100 ? characteristics test items test conditions resistor type guaranteed value jumper type resistancevariation of resistance with temperature solderability damp heat, steady state endurance at 70 c endurance rapid change of temperature bend strength of the end face plating resistance to solvent resistance to soldering heat overload (2.0% + 0.1 ) max. 50m (1.0% + 0.05 ) (3.0% + 0.1 ) max. 50m max. 100m see "products list"see "products list" 20 c no remarkable abnormality on the appearance. a new uniform coating of minimum of95% of the surface being immersed and no soldering damage. without mechanical damage such as breaks. compliance standard(s) : iec60115 ? 8 jisc 5201 ? 8 measurement : + 20 / ? 55 / + 20 / + 125 c soldering condition : 260 5 c duration of immersion : 10 1s 40 c, 93%rh (relative humidity) test time : 1,000h to 1,048h (3.0% + 0.1 ) (3.0% + 0.1 ) (1.0% + 0.05 ) (1.0% + 0.05 ) (1.0% + 0.05 ) max. 100m max. 100m max. 50m max. 50m max. 50m 70 c rated voltage (current)1.5h : on ? 0.5h : off test time : 1,000h to 1,048h125 c (mcr006 / 25 / 50 / 100) 155 c (mcr01 / 03 / 10 / 18) test time : 1,000h to 1,048h23 5 c , immersion cleaning, 5 0.5min solvent : 2 ? propanol ? test temp. ? 55 c to + 125 c 100cycle (mcr006 / 01 / 03) ? 55 c to + 125 c 5cycle (mcr10 / 18 / 25 / 50 / 100) rosinethanol : 25% (weight)soldering c ondition : 2 4 5 5 c duration of immersion : 2.0 0.5s mcr100 maximum overload voltage (test voltage) 30v mcr01 mcr03 mcr18 400v mcr025 400v mcr50 400v 400v test voltage is the smaller one of 1 or 2 1 rated voltage (current) 2.5, 2s. 2 maximum overload voltage mcr10 200v 100v 100v mcr006 50v mcr004 mcr01 / 03 / 10 / 18 / 25 / 50 0 20 40 60 80 100 ? 55 0 70 100 155 ambient temperature ( c) percent rated power (%) downloaded from: http:///
5/6 da t asheet mcr series www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2016.06 - rev.j ? tape dimensions 0.38 0.03 0.68 0.03 0.7 0.1 1.2 0.1 1.1 0.1 1.9 0.1 (unit : mm) 0.24 0.03 0.45 0.03 8.0 0.2 mcr004 yzp 3.5 0.05 1.75 0.1 1.5 + 0.1 0 2.0 0.05 max 0.5 mcr004 yzp 4.0 0.1 2.0 0.05 w type code part no. f e a 0 b 0 8.0 0.2 mcr006 ylp 3.5 0.05 1.75 0.1 8.0 0.3 mcr01 mzp 3.5 0.05 1.75 0.1 8.0 0.3 mcr03 ezp 3.5 0.05 1.75 0.1 8.0 0.3 mcr10 ezp 3.5 0.05 1.75 0.1 8.0 0.3 mcr18 ezp 3.5 0.05 1.75 0.1 1.5 + 0.1 0 1.65 + 0.2 ? 0.1 2.4 + 0.2 ? 0.1 3.5 + 0.15 ? 0.05 1.95 + 0.1 ? 0.05 1.5 + 0.1 0 1.5 + 0.1 0 1.5 + 0.1 0 1.5 + 0.1 0 2.0 0.05 max 0.5 2.0 0.05 2.0 0.05 2.0 0.05 2.0 0.05 max 1.1max 1.1 max 1.1 max 1.1 d 0 type code part no. p 0 p 1 p 2 t 2 4.0 0.1 4.0 0.1 4.0 0.1 4.0 0.1 4.0 0.1 mcr006 ylp 2.0 0.05 mcr01 mzp 2.0 0.05 mcr03 ezp 4.0 0.1 mcr10 ezp 4.0 0.1 mcr18 ezp 4.0 0.1 3.0 0.1 3.5 0.1 3.4 0.2 5.6 0.2 3.5 0.2 6.7 0.2 (unit : mm) w type code part no. f e a 0 b 0 8.0 0.3 mcr25 jzh 3.5 0.05 1.75 0.1 12 0.3 mcr50 jzh 5.5 0.05 1.75 0.1 12 0.3 mcr100 jzh 5.5 0.05 1.75 0.1 1.5 + 0.1 0 1.5 + 0.1 0 1.5 + 0.1 0 2.0 0.05 max 1.1 2.0 0.05 2.0 0.05 max 1.1max 1.1 d 0 type code part no. p 0 p 1 p 2 t 2 4.0 0.1 4.0 0.1 4.0 0.1 mcr25 jzh 4.0 0.1 mcr50 jzh 4.0 0.1 mcr100 jzh 4.0 0.1 paper tape p 0 p 2 p 1 e f w t 2 d 0 a 0 b 0 base paper (bottom tape) components cavity top tape embossed tape a 0 p 1 p 0 p 2 b 0 f w t 2 e d 0 downloaded from: http:///
6/6 da t asheet mcr series www.rohm.com c 2015 rohm co., ltd. all rights reserved. 2016.06 - rev.j ? reel dimensions a type code part no. b c d (unit : mm) 13 0.2 180 0 ? 1.5 60 + 1.0 0 mcr006 ylp mcr01 mzp mcr03 ezp mzp mcr10 ezp mcr18 ezp mcr25 jzh mcr50 jzh mcr100 jzh 9 + 1.0 0 13 + 1.0 0 mcr004 yzp 0 2 0 4 0 6 0 8 0 2 0 4 0 6 0 8 c a bd label according to eiaj et-7200b label a b d c according to eiaj et-7200b (rrv) 1 mcr004 / 006 / 01 / 03 / 10 / 18 / 25 / 50 / 100 2 mcr004 / 006 / 01 / 03 / 10 / 18 / 25 downloaded from: http:///
datasheet d a t a s h e e t notice-paa-e rev.001 ? 2015 rohm co., ltd. all rights reserved. notice precaution on using rohm products 1. if you intend to use our products in devices requiring extremely high reliability (such as medical equipment (note 1) , aircraft/spacecraft, nuclear power controllers, etc.) and whos e malfunction or failure may cause loss of human life, bodily injury or serious damage to property (specific applications), please consult with the rohm sales representative in advance. unless otherwise agreed in writ ing by rohm in advance, rohm shall not be in any way responsible or liable for any damages, expenses or losses in curred by you or third parties arising from the use of any rohms products for specific applications. (note1) medical equipment classification of the specific applications japan usa eu china class class class b class class ? class 2. rohm designs and manufactures its products subject to strict quality control system. however, semiconductor products can fail or malfunction at a certain rate. please be sure to implement, at your own responsibilities, adequate safety measures including but not limited to fail-safe desi gn against the physical injury, damage to any property, which a failure or malfunction of our products may cause. the following are examples of safety measures: [a] installation of protection circuits or other protective devices to improve system safety [b] installation of redundant circuits to reduce the impact of single or multiple circuit failure 3. our products are not designed under any special or extr aordinary environments or conditi ons, as exemplified below. accordingly, rohm shall not be in any way responsible or liable for any damages, expenses or losses arising from the use of any rohms products under an y special or extraordinary environments or conditions. if you intend to use our products under any special or extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of product performance, reliability, etc, prior to use, must be necessary: [a] use of our products in any types of liquid, incl uding water, oils, chemicals, and organic solvents [b] use of our products outdoors or in places where the products are exposed to direct sunlight or dust [c] use of our products in places where the products ar e exposed to sea wind or corrosive gases, including cl 2 , h 2 s, nh 3 , so 2 , and no 2 [d] use of our products in places where the products are exposed to static electricity or electromagnetic waves [e] use of our products in proximity to heat-producing components, plastic cords, or other flammable items [f] sealing or coating our products with resin or other coating materials [g] use of our products without cleaning residue of flux (ev en if you use no-clean type fluxes, cleaning residue of flux is recommended); or washing our products by using water or water-soluble cleaning agents for cleaning residue after soldering [h] use of the products in places subject to dew condensation 4. the products are not subjec t to radiation-proof design. 5. please verify and confirm characteristics of the final or mounted products in using the products. 6. in particular, if a transient load (a large amount of load applied in a short per iod of time, such as pulse. is applied, confirmation of performance characteristics after on-boar d mounting is strongly recomm ended. avoid applying power exceeding normal rated power; exceeding the power rating under steady-state loading c ondition may negatively affect product performance and reliability. 7. de-rate power dissipation (pd) depending on ambient temper ature (ta). when used in seal ed area, confirm the actual ambient temperature. 8. confirm that operation temperat ure is within the specified range described in the product specification. 9. rohm shall not be in any way responsible or liable for fa ilure induced under deviant condi tion from what is defined in this document. precaution for mounting / circuit board design 1. when a highly active halogenous (chlori ne, bromine, etc.) flux is used, the resi due of flux may negatively affect product performance and reliability. 2. in principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must be used on a through hole mount products. if the flow sol dering method is preferred on a surface-mount products, please consult with the rohm representative in advance. for details, please refer to rohm mounting specification downloaded from: http:///
datasheet d a t a s h e e t notice-paa-e rev.001 ? 2015 rohm co., ltd. all rights reserved. precautions regarding application examples and external circuits 1. if change is made to the constant of an external circuit, pl ease allow a sufficient margin considering variations of the characteristics of the products and external components, including transient characteri stics, as well as static characteristics. 2. you agree that application notes, re ference designs, and associated data and in formation contained in this document are presented only as guidance for products use. theref ore, in case you use such information, you are solely responsible for it and you must exercise your own independent verification and judgment in the use of such information contained in this document. rohm shall not be in any way responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of such information. precaution for electrostatic this product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. please take proper caution in your manufacturing process and storage so that voltage exceeding t he products maximum rating will not be applied to products. please take special care under dry condit ion (e.g. grounding of human body / equipment / solder iron, isolation from charged objects, se tting of ionizer, friction prevention and temperature / humidity control). precaution for storage / transportation 1. product performance and soldered connections may deteriora te if the products are stor ed in the places where: [a] the products are exposed to sea winds or corros ive gases, including cl2, h2s, nh3, so2, and no2 [b] the temperature or humidity exceeds those recommended by rohm [c] the products are exposed to di rect sunshine or condensation [d] the products are exposed to high electrostatic 2. even under rohm recommended storage c ondition, solderability of products out of recommended storage time period may be degraded. it is strongly recommended to confirm sol derability before using products of which storage time is exceeding the recommended storage time period. 3. store / transport cartons in the co rrect direction, which is indicated on a carton with a symbol. otherwise bent leads may occur due to excessive stress applied when dropping of a carton. 4. use products within the specified time after opening a humidity barrier bag. baking is required before using products of which storage time is exceeding the recommended storage time period. precaution for product label qr code printed on rohm products label is for rohms internal use only. precaution for disposition when disposing products please dispose them proper ly using an authorized industry waste company. precaution for foreign exchange and foreign trade act since concerned goods might be fallen under listed items of export control prescribed by foreign exchange and foreign trade act, please consult with rohm in case of export. precaution regarding intellectual property rights 1. all information and data including but not limited to application example contained in this document is for reference only. rohm does not warrant that foregoi ng information or data will not infringe any intellectual property rights or any other rights of any third party regarding such information or data. 2. rohm shall not have any obligations where the claims, actions or demands arising from the co mbination of the products with other articles such as components, circuits, systems or external equipment (including software). 3. no license, expressly or implied, is granted hereby under any intellectual property rights or other rights of rohm or any third parties with respect to the products or the informati on contained in this document. pr ovided, however, that rohm will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to manufacture or sell products containing the produc ts, subject to the terms and conditions herein. other precaution 1. this document may not be reprinted or reproduced, in whol e or in part, without prior written consent of rohm. 2. the products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written consent of rohm. 3. in no event shall you use in any wa y whatsoever the products and the related technical information contained in the products or this document for any military purposes, incl uding but not limited to, the development of mass-destruction weapons. 4. the proper names of companies or products described in this document are trademarks or registered trademarks of rohm, its affiliated companies or third parties. downloaded from: http:///
datasheet datasheet notice C we rev.001 ? 201 5 rohm co., ltd. all rights reserved. general precaution 1. before you use our pro ducts, you are requested to care fully read this document and fully understand its contents. rohm shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny rohms products against warning, caution or note contained in this document. 2. all information contained in this docume nt is current as of the issuing date and subj ec t to change without any prior notice. before purchasing or using rohms products, please confirm the la test information with a rohm sale s representative. 3. the information contained in this doc ument is provi ded on an as is basis and rohm does not warrant that all information contained in this document is accurate an d/or error-free. rohm shall not be in an y way responsible or liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or concerning such information. downloaded from: http:///
|
